engine dont run... 6.0 powerstroke

Ford Forum Ford Classifieds Photo Gallery Member List Search Ford Recalls Contact FF Sponsors
Ford News Ford Lineup Forum FAQ Calendars Ford TSB's Register Login

engine dont run... 6.0 powerstroke

Printable Version

Ford Forums >> Ford Trucks, Ford Vans & Ford SUV's >> Ford Excursion >> engine dont run... 6.0 powerstroke

Page: [1] 2 next > >>

Message

<< Older Topic Newer Topic >>

engine dont run... 6.0 powerstroke - 11/29/2007 9:07:36 AM

bonboy

Posts: 13
Score: 0
Joined: 5/8/2007
Status: offline

i drive and the engine dead.... and dont start..... i have take diagnostic sistem and the error code is: icp sensor, if i try to put start spray the car turn on and run only idle....

excuse me for my incorrect language.

thank you

Post #: 1

RE: engine dont run... 6.0 powerstroke - 11/29/2007 3:24:08 PM

BRETM

Official Site Sponsor
Posts: 257
Score: 0
Joined: 11/9/2007
Status: offline

Is it a crank, no start? What code was it? What year Excursion? Need more info to help.

_____________________________

www.discountedgenuinefordparts.com

(in reply to bonboy)

Post #: 2

RE: engine dont run... 6.0 powerstroke - 11/29/2007 11:57:12 PM

bonboy

Posts: 13
Score: 0
Joined: 5/8/2007
Status: offline

yes cranking is ok but not start.... error is 2291, the car is 2005 , the engine turn off when i driving ....
excuse me for my incorrect language.....i m italian mechanics and here this car is not official imported.
We dont have more info of this engine.
i think is pressure sensor but i whant know more possibility for order in usa parts, but is very expensive and i need more time for shipping.
Thank You

(in reply to BRETM)

Post #: 3

RE: engine dont run... 6.0 powerstroke - 11/30/2007 8:08:17 AM

BRETM

Official Site Sponsor
Posts: 257
Score: 0
Joined: 11/9/2007
Status: offline

First, you need to monitor ICP voltage KOEO, see if it is biased low, no less than 0.15V. Then monitor ICP while cranking engine, see if it builds up 500 psi. May have high pressure oil system leak, bad pump, ICP sensor, or IPR solenoid. But that would be the first check to do. Then if it doesn't build 500 psi, you need to air check the high pressure system for leaks, but you need a diagnostic tool that can do active commands to close the IPR solenoid.

_____________________________

www.discountedgenuinefordparts.com

(in reply to bonboy)

Post #: 4

RE: engine dont run... 6.0 powerstroke - 12/5/2007 12:42:06 AM

bonboy

Posts: 13
Score: 0
Joined: 5/8/2007
Status: offline

where is located icp sensor exact???
but in 2005 i think is not same 2000....

(in reply to BRETM)

Post #: 5

RE: engine dont run... 6.0 powerstroke - 12/5/2007 7:15:15 AM

Hayapower

Posts: 2082
Score: 0
Joined: 7/22/2006
Status: offline

05 has the ICP in the right/passenger valve cover... A diagnostic should be run to to prove out the sensor as faulted though, prior to replacement...

Thumbnail Image

Attachment (1)

_____________________________

05 F250 C/C FX4 6.0
1969 Firebird Trans Am
2003 Hayabusa GSXR1300

(in reply to bonboy)

Post #: 6

RE: engine dont run... 6.0 powerstroke - 12/6/2007 3:28:47 AM

bonboy

Posts: 13
Score: 0
Joined: 5/8/2007
Status: offline

today i change sensore .. (i have another car in garage) but the problem is same... i can try whit spray starter for diesel engine.. and the engine star... the iddle is no good and enfine is very noise.....
is possible this is a problem hight pressure pump or iniector??
i have same problem whit one italian car whit common rail iniection... but i dont know is same .. or this model powerstroke have some difect..

(in reply to Hayapower)

Post #: 7

RE: engine dont run... 6.0 powerstroke - 12/6/2007 7:36:51 AM

bonboy

Posts: 13
Score: 0
Joined: 5/8/2007
Status: offline

in cranking i have 500psi in iniector control pressure.... i think is iniectore broke...

(in reply to bonboy)

Post #: 8

RE: engine dont run... 6.0 powerstroke - 12/7/2007 3:29:20 AM

bonboy

Posts: 13
Score: 0
Joined: 5/8/2007
Status: offline

anyone know pressur of pump in gas tank?