1998 Taurus Instrument Cluster Help Please
#1
1998 Taurus Instrument Cluster Help Please
Hello all,
I just recently purchased a 1998 Taurus with the duratech engine. 1 I have a few probems I could really Please use help on.
1.) Alot of Instrument Cluster lights are inop to include the following:
O/D off, Rear Lamp Out,ABS,Cruise,Brake. I have checked (with an ohm meter) all fuses, removed panel and checked bulbs, checked power at fuse 12 (which I think powers it) and searched high and low for a plug which may be unplugged. Its driving me NUTS..
2.) Cruise control is inop: I have check the brake switch, attempted to check the servo but NO wiring diagrams at the library match the colors. It is a 6 pin connector. I have voltage on 2 of the pins at all times (dont know which way to count the pin out.) I am hoping its related to the above problem????
3.) Also the engine runs ar about 2600 RPM's at 70mph. I dont know if this is correct or not?
My wife drove it the other day and said the O/D light came on and started flashing. I have not seen this YET and have put about 100 miles on it since. Heck the light doesnt even test now so I dont know what happened after that.
4.) Last but not least. The service engine light came on. Autozone did the diagnosis on it and said it was the EGR valve. I did buy a new one but before I changed it I checked the vaccum line and there was very little suction on the line. Although I dont know how much is suppose to be there either?
Please help...... I have to drive this thing from michigan to alabama next week and cant risk not being there to start a new job.
Thank you Chad
I just recently purchased a 1998 Taurus with the duratech engine. 1 I have a few probems I could really Please use help on.
1.) Alot of Instrument Cluster lights are inop to include the following:
O/D off, Rear Lamp Out,ABS,Cruise,Brake. I have checked (with an ohm meter) all fuses, removed panel and checked bulbs, checked power at fuse 12 (which I think powers it) and searched high and low for a plug which may be unplugged. Its driving me NUTS..
2.) Cruise control is inop: I have check the brake switch, attempted to check the servo but NO wiring diagrams at the library match the colors. It is a 6 pin connector. I have voltage on 2 of the pins at all times (dont know which way to count the pin out.) I am hoping its related to the above problem????
3.) Also the engine runs ar about 2600 RPM's at 70mph. I dont know if this is correct or not?
My wife drove it the other day and said the O/D light came on and started flashing. I have not seen this YET and have put about 100 miles on it since. Heck the light doesnt even test now so I dont know what happened after that.
4.) Last but not least. The service engine light came on. Autozone did the diagnosis on it and said it was the EGR valve. I did buy a new one but before I changed it I checked the vaccum line and there was very little suction on the line. Although I dont know how much is suppose to be there either?
Please help...... I have to drive this thing from michigan to alabama next week and cant risk not being there to start a new job.
Thank you Chad
#3
Update: I tested the O/D light with the switch. It DOES illuminate and work fine..... So now I am completely baffeled???
There has got to be a relay, junction point or something in common.... Its driving me nuts now!!!
There has got to be a relay, junction point or something in common.... Its driving me nuts now!!!
#4
I've got a great mechanic in Livonia, Van Ess & Sons on Five Mile Rd (corner of Harrison) Stu the owner, has been serviceing my 98 SE Wagon for a couple of years now. He typically can tell you within an hour whats wrong with the vehicle. He's been rated as #1 in Livonia for years. You can reach him at 734-422-0320, M-F 9am-5pm.
I've been doing business with him for at least ten years and recommend him to everyone. I'm not related to him and am not affiliated with him other than a very satisfied customer. His attitude and prices are great. Good luck!
I've been doing business with him for at least ten years and recommend him to everyone. I'm not related to him and am not affiliated with him other than a very satisfied customer. His attitude and prices are great. Good luck!
Thread
Thread Starter
Forum
Replies
Last Post