2017 ford driver seat cushion

Reply Subscribe

Thread Tools

Search this Thread

Jun 11, 2020 | 06:57 PM

ford17

Thread Starter

Junior Member

Joined: Jun 2020

Posts: 2

2017 ford driver seat cushion

Does any have a link or know how to remove and replace driverside seat cusion ? I cannot find anything on this any help would be appreciated.

Jun 12, 2020 | 08:30 AM

Hayapower

Super Moderator

Joined: Jul 2006

Posts: 7,555

Welcome to the site

2017 Ford what?

Jun 12, 2020 | 09:27 AM

ford17

Thread Starter

Junior Member

Joined: Jun 2020

Posts: 2

F150

2017 ford f150

Jun 21, 2020 | 08:16 AM

scott.butler4

Senior Member

Joined: Apr 2020

Posts: 1,077

Front Seat Cushion Cover

Removal

NOTE: Driver seat shown, passenger seat similar.

NOTE: Seat backrest blower motor without snorkel shown, unless otherwise called out.

NOTE: Removal steps in this procedure may contain installation details.

Passenger seat

Remove the OCS.
Refer to: Occupant Classification System (OCS) Sensor - Vehicles With: Multi-Contour Seats (501-20B Supplemental Restraint System, Removal and Installation).
Refer to: Occupant Classification System (OCS) Sensor - Vehicles Without: Multi-Contour Seats (501-20B Supplemental Restraint System, Removal and Installation).

Driver seat

Remove the front seat.

Remove the side shield screws.

Manual seat

1. Remove the clip and the recline handle.
1. If equipped.
  Remove the clip and the lumbar handle.

Remove the side shield.
1. Firmly grasp the side shield, lift up and out, separating the side shield from the recliner bracket.
1. From underneath, squeeze the retainers together and pull out on the side shield.
1. Slide the side shield forward.

Power Seat

If equipped.
Remove the clip and the recline handle.

Remove the side shield.
1. Lift up on the rear of the side shield and pull outward.
1. Slide the side shield forward.
1. Disconnect the electrical connector.

All seats

Release the elastic strap from the seatbelt buckle.

Position the backrest wire harness(es) aside.
1. Release the electrical connector retainer(s) from the seat track.
1. Release the locking tab(s) and disconnect the backrest wire harness electrical connector(s).

1. Detach the backrest cover straps.
1. If equipped.
  Route the backrest cover straps through the backrest blower motor snorkel.
1. Position the backrest cover upward.

Detach the cushion cover J-clips and position the cushion cover upward.

Multi-contour seat

Detach the backrest cover lower J-clips.

1. NOTE: To install, gradually alternate the left and right seat backrest cover zippers to prevent damage to the seat backrest cover.
  Unzip the backrest cover zipper on each side.
1. Position the backrest cover up.

NOTE: For installation of a backrest blower motor with snorkel, note the routing of the snorkel.
Detach the hook-and-loop retainer and position the backrest cover strap aside.

Detach the multi-contour seat cushion hose retainer.

Release the locking tab and disconnect the hose coupling assembly (orange) from the SCMG.

Feed the multi-contour seat hose assembly out through the backrest cover opening.

All seats

If equipped.
Disconnect the cushion heater mat electrical connector.

Detach the J-clip and position aside.

Release the J-clips and position the front of the seat cushion cover and foam assembly slightly upwards.

If equipped.
Detach the cushion heater mat J-clip.

Remove the seat cushion cover and foam as an assembly.

NOTE: This step is only necessary when installing a new component.
Invert the rear portion of the seat cushion cover.

NOTICE: Use care when separating the seat cushion from the hook-and-arrow or the hook may be torn from the seat cushion foam pad.

NOTE: This step is only necessary when installing a new component.

Remove the seat cushion cover.
1. Invert the seat cushion cover.
1. Release the hook-and-arrows.